DS100 - Dining Table Set Plans - Woodworking Plans - Outdoor Furniture Plans
Oversize: 11' 1 3/4" x 8' 1 3/4" for a Set
2' 1 1/4" x 2' 2 1/2" for a chair
3' 3 1/2" x 6' 4 1/2" for a Table
DS100 - Dining Table Set Plans - Woodworking Plans
Outdoor Furniture Plans
Outdoor Furniture Plans
Oversize:
7' 10 1/2" x 7' 10 3/4" for a Set
1' 9 1/8" x 1' 8" for a chair
7' 10 1/2" x 6' 4 1/2" for a Table
Dimensional lumber sizes:
a: 2"x3" (Nominal) = 1 1/2" x 2 1/2" (Actual)
b: 2"x4" (Nominal) = 1 1/2" x 3 1/2" (Actual)
c: 2"x2" (Nominal) = 1 1/2" x 1 1/2" (Actual)
d: 2"x6" (Nominal) = 1 1/2" x 5 1/2" (Actual)
e: 1"x4" (Nominal) = 3/4" x 3 1/2" (Actual)
f: 1"x8" (Nominal) = 3/4" x 7 1/4" (Actual)
1' 9 1/8" x 1' 8" for a chair
7' 10 1/2" x 6' 4 1/2" for a Table
Dimensional lumber sizes:
a: 2"x3" (Nominal) = 1 1/2" x 2 1/2" (Actual)
b: 2"x4" (Nominal) = 1 1/2" x 3 1/2" (Actual)
c: 2"x2" (Nominal) = 1 1/2" x 1 1/2" (Actual)
d: 2"x6" (Nominal) = 1 1/2" x 5 1/2" (Actual)
e: 1"x4" (Nominal) = 3/4" x 3 1/2" (Actual)
f: 1"x8" (Nominal) = 3/4" x 7 1/4" (Actual)
Units: Inches - fractions
DS100 - Dining Table Set Plans - Woodworking Plans
Outdoor Furniture Plans
The Upgrade plan for
Detailed plans for construction
Unit Inches - fractions
DS100 - Dining Table Set Plans - Woodworking Plans
Outdoor Furniture Plans
...
(Newly Upgraded Version)
...
I'm upgrading the entire plan, and I always do so, I am reducing the volume of wood in construction and still achieve what we want, to save money, build faster, easier,
I am presenting a plan for a better way with less drawing, to save money on printing and viewing time, download time,
I am following the suggestions and feedback from all of you,
...
Thanking you for all of your hard work and wonderful plans...Wishing you the best.
ReplyDeleteOk! Viola :)
DeleteA plan that provides you a really nice and amazing. Thank
ReplyDeleteکرکره برقی-درب اتوماتیک-پارتیشن اداری-پارتیشن-درب ضد سرقت-تور چین-لیزینگ خودرو-ایران خودرو
Why do you supply the measurements but not the degrees for the angled cuts in your drawings. I would like to make some of the ds100 chairs but there are no angle indications for the front and back legs, or if the measurements are including the angles or before the angles are cut.
ReplyDeleteNice blog, The points which are included in this blog are really very informative for me. Thanks a lot for sharing. Garage Door Repair
ReplyDeleteNice Post
ReplyDelete